Summer Starts Here - Save up to 70%
Trailer Wiring Harness Installation - 2005 Chevrolet Uplander- Video
Today on our 2005 Chevrolet Uplander we'll be installing the Tow Ready T-One Connector Trailer Wiring Kit part number 118396. To begin with here, we'll need to raise the rear hatch of the vehicle. Next we'll need to remove two torques head bolts from each light assembly. The size of the torques head is a T30. We can go ahead and gently pull the light assembly off of the vehicle, making sure that we don't break any of the tabs that are on the forward most portion of the light assembly. With the light assembly out, we can go ahead and remove the electrical from behind. To do this, we'll squeeze the tab on the wiring and gently pull down. We can go ahead and set the light assembly aside for right now. more
11/13/2014 9:04:37 PM
Trailer Wiring Harness Installation - 2006 Chevrolet Uplander- Video
Today on our 2006 Chevrolet Uplander, well be installing the Curt T-Connector Vehicle Wiring Harness part number 56077. Now we need to use our trailer wiring, lets pull it out of the vehicle and well run it down by our hitch. The weather stripping is thick enough on here where itll protect the wire when we close the door. One thing we do want to make sure of is that we stay about four to five inches away from the lock for the door just to make sure we dont do any damage to the wiring harness. Well pull out the amount we need and hook it up to our trailer or whatever well be towing. When were done using our wiring harness, well just store it back inside of our vehicle to keep it out of the elements and off the road to protect the wiring. With the rear of the van already open, well go ahead and get ready to start our installation. more
10/15/2014 12:26:57 PM
Trailer Wiring Harness Installation - 2008 Chevrolet Uplander- Video
Today on our 2008 Chevy Uplander well be installing the Tow Ready T1 connector part #: 118396. To begin our installation well first need to open up the rear cargo door. Then well remove the two fasteners securing the driver side taillight assembly. As you pull and pry the taillight assembly away from the vehicle be careful not to break the alignment tabs that are hidden in behind the lens assembly. Next well go ahead and remove the manufactures connection to the taillight assembly. Simply press on the lock of the connector and pull it away from the assembly. more
5/31/2012 1:32:34 PM
Trailer Wiring Harness Installation - 2006 Chevrolet Uplander 118396- Video
Today on this 2006 Chevrolet Uplander we are going to be installing wiring harness part number 118396. The ports that we are going to be plugging our wiring harness into are located behind the tail light assemblies on both the driver and passenger sides of the vehicle. The first thing we are going to do is remove both of the tail light assemblies. To do that we need to remove the inboard side screws that you can see once you have lifted up your cargo door. With those screws removed if you gently rock the tail light assembly back and forth you should be able to release the outboard side clips as well. If you look on the back side of it you can see the port that we are going to be plugging our wiring harness into. To separate the two halves there is a little release button on the top side. You just want to press that in and pull it away from the tail light. 00:48 more
12/28/2010 8:08:44 AM
Trailer Wiring Harness Installation - 2006 Chevrolet Uplander 118396- Video
Today on this 2006 Chevrolet Uplander we are going to install part number 118396, the t-one wiring harness from Tow Ready. We are also going to install part number 37185, the adapter 4-pole to 7 and 4-pole multi-tool connector. The first step that we are going to do is go ahead and open up the hatch of this vehicle and remove both taillights. Alright and this is our connection point right here. And we are going disconnect. Push down on this tab here and it comes apart. We are going to repeat the same process on the passenger side. Are next step is to take the t-one wiring harness and the 4-pole part. We are going to tuck it behind the bumper here. Have it out of the bottom so we can pull it over by the hitch. And then we are going to take our connection with the yellow and brown wires and we are going to install that on to the wire harness that comes out from the van. So let us go ahead and snap those two together. We are going to leave that be for now. And then our connection with the green wire, that is going to get routed on to the other side of the vehicle, on the passenger side. So we are just going to take this and just tuck it on down and pull it out the bottom too. With this, we are just going to go ahead and reinstall our taillight and hook up the taillight electrical to this connection right here and reinstall the whole taillight assembly back onto the vehicle. 1:13 more
4/20/2010 3:33:19 AM
Trailer Wiring Harness Installation - 2006 Chevy Uplander- Video
First well open up the rear door and start disassembling the tail lights and take them off the body. Well go ahead and take off one of the tail lights here. There are two torque bolts that need to be taken out and light pops off from the housing. Okay the lights are off so now its time to start installing the wire. What well do is push the four pole through the cavity between the bumper and the body and out the bottom plus the end for the passengers side too. Well leave the end for the drivers side tail light up in the air, well make the connections with the harness and the tail light. With the drivers side tail light re-installed, pull out all your slack on your line here, what well do next is thread it through behind these bumper brackets. Well go across all four of them, what well do is take some extra zip ties and tie it to that so they wont be dangling and in the way. Now that we have gotten to the other side of the vehicle, well take our T-1 connector passenger side end and push it up the pocket and pull it out the other side. Now well pull the harness out of the cavity and go ahead and make our connections. While were at it well take up a little bit of slack by using the zip tie to tie the wire to itself. While were her well install our ground wire. Now we re-install our passenger light. more
8/8/2008 4:29:39 AM
Filter Videos
Filter Videos
